收藏本站
ADT7468
1
9
1
9
SCL
SDA
0
1
0
1
1
1
0
R/W
D7
D6
D5
D4
D3
D2
D1
D0
START BY
ACK. BY
ACK. BY
STOP BY
MASTER
FRAME 1
ADT7468
FRAME 2
ADT7468
MASTER
SERIAL BUS ADDRESS BYTE
ADDRESS POINTER REGISTER BYTE
Figure 17. Writing to the Address Pointer Register Only
1
9
1
9
SCL
SDA
0
1
0
1
1
1
0
R/W
D7
D6
D5
D4
D3
D2
D1
D0
START BY
ACK. BY
NO ACK. BY STOP BY
MASTER
FRAME 1
ADT7468
FRAME 2
MASTER
MASTER
SERIAL BUS ADDRESS BYTE
DATA BYTE FROM ADT7468
Figure 18. Reading Data from a Previously Selected Register
It is possible to read a data byte from a data register without
first writing to the address pointer register, if the address
pointer register is already at the correct value. However, it is not
possible to write data to a register without writing to the
address pointer register, because the first data byte of a write is
always written to the address pointer register.
In addition to supporting the send byte and receive byte
2.
3.
4.
5.
6.
The master sends the 7-bit slave address followed by the
write bit (low).
The addressed slave device asserts ACK on SDA.
The master sends a command code.
The slave asserts ACK on SDA.
The master asserts a stop condition on SDA and the
protocols, the ADT7468 also supports the read byte protocol.
(See Intel’s System Management Bus Specifications Rev. 2 for
more information.)
If several read or write operations must be performed in
transaction ends.
For the ADT7468, the send byte protocol is used to write a
register address to RAM for a subsequent single byte read from
the same address. This operation is illustrated in Figure 19.
succession, the master can send a repeat start condition instead
of a stop condition to begin a new operation.
WRITE OPERATIONS
1
S
2
SLAVE
ADDRESS
3
W A
4
REGISTER
ADDRESS
5 6
A P
The SMBus specification defines several protocols for different
types of read and write operations. The ones used in the
ADT7468 are discussed below. The following abbreviations are
used in the diagrams:
S: START
P: STOP
R: READ
W: WRITE
A : ACKNOWLEDGE
Figure 19. Setting a Register Address for a Subsequent Read
If the master is required to read data from the register
immediately after setting up the address, it can assert a repeat
start condition immediately after the final ACK and carry out a
single byte read without asserting an intermediate stop
condition.
Write Byte
In this operation, the master device sends a command byte and
one data byte to the slave device, as follows:
A: NO ACKNOWLEDGE
The ADT7468 uses the following SMBus write protocols.
Send Byte
In this operation, the master device sends a single command
byte to a slave device as follows:
1.
2.
3.
4.
The master device asserts a start condition on SDA.
The master sends the 7-bit slave address followed by the
write bit (low).
The addressed slave device asserts ACK on SDA.
The master sends a command code.
1.
The master device asserts a start condition on SDA.
5.
The slave asserts ACK on SDA.
Rev. 3 | Page 13 of 81 | www.onsemi.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ADT7473ZEVB BOARD EVALUATION FOR ADT7473
ADT7475EBZEVB BOARD EVALUATION FOR ADT7475
ADT7476EBZEVB BOARD EVALUATION FOR ADT7476
ADT7490ZEVB BOARD EVALUATION FOR ADT7490
ADZS-21262-1-EZEXT BOARD DAUGHTER FOR ADSP-21262
ADZS-BF-EZEXT-1 BOARD DAUGHTER ADSP-BF533/561KIT
ADZS-BFAV-EZEXT BOARD DAUGHT ADSP-BF533,37,61KIT
ADZS-BFSHUSB-EZEXT BOARD DAUGHTER EZ EXTENDER
相关代理商/技术参数
ADT7470 制造商:AD 制造商全称:Analog Devices 功能描述:Temperature Sensor Hub and Fan Controller
ADT7470_13 制造商:AD 制造商全称:Analog Devices 功能描述:Temperature Sensor Hub and Fan Controller
ADT7470ARQ 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (I2C) 16-Pin QSOP
ADT7470ARQ-REEL 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADT7470ARQ-REEL7 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (I2C) 16-Pin QSOP T/R
ADT7470ARQZ 功能描述:IC SENSOR TEMP FAN CTRLR 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:3,000 系列:- 功能:温度开关 传感器类型:内部 感应温度:85°C 分界点 精确度:±6°C（最小值） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:开路漏极 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:ADT6501SRJZP085RL7-ND
ADT7470ARQZ-REEL 功能描述:IC SENSOR TEMP FAN CTRLR 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:2,500 系列:SilentSense™ 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-55°C ~ 125°C，外部传感器 精确度:±2°C 本地（最大），±3°C 远程（最大） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:I²C?/SMBus? 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) 其它名称:MIC284-2BMMTRMIC284-2BMMTR-ND
ADT7470ARQZ-REEL7 功能描述:IC SENSOR TEMP FAN CTRLR 16QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:2,500 系列:SilentSense™ 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-55°C ~ 125°C，外部传感器 精确度:±2°C 本地（最大），±3°C 远程（最大） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:I²C?/SMBus? 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) 其它名称:MIC284-2BMMTRMIC284-2BMMTR-ND